Randy, a General Contractor in Dallas, TX and Owner of www.RSquaredRenovations.com, demonstrates how to install the plumbing for a bathroom faucet drain. If you are in the Dallas area and are looking to remodel your bathroom, give him a call at 972-998-8544. www.UniqueVanities.com Here we have the countertop sitting on the vanity, We've bought ap trap installation kit. You can get it at any home improvement store. It comes with the P trap itself. That's what we are looking for. The trap holds water in here so you don't get sewer gas coming up back through. We have a trap adapter mounted here. Essentially all these fittings are slip joint fittings. There is a plastic washer that has a cone shape. it's what seals the pipe. It acts like a compression fitting that will seal this pipe onto that fitting there. These have wings on them so they all need to be hand tightened. You really don't need a wrench for these to fit together properly. Using a wrench would just cause them to break. We have a 6 inch tail piece extension that will go on the bottom of the drain that came with our faucet. That slips into here and everything is adjustable. You have about an inch and a half worth of play in both of these up and down. Everything should go together without cutting anything and just by hand tightening everything. If these parts are a little too long, they do make them in a 12 inch extension if your drain coming out of the wall was lower and you had a higher vanity they come in a 12 ...
Sunday, December 25, 2011
Thursday, December 22, 2011
Justrite 7250130 Galvanized Steel, AccuFlow Type II Red Safety Can with 1" Flexible Spout, Large ID zone, Meets OSHA & NFPA For Handling Hazardous liquids. 5 Gallon (19L) Size.
!±8± Justrite 7250130 Galvanized Steel, AccuFlow Type II Red Safety Can with 1" Flexible Spout, Large ID zone, Meets OSHA & NFPA For Handling Hazardous liquids. 5 Gallon (19L) Size.
Brand : Justrite - AccuFlow | Rate : 
| Price : $64.71
Post Date : Dec 22, 2011 05:42:12 | Usually ships in 24 hours
| Price : $64.71Post Date : Dec 22, 2011 05:42:12 | Usually ships in 24 hours
- Large ID zone permits user labeling of contents to avoid misuse
- Stainless steel flame arrester for exceptional corrosion protection - reliably dissipates heat to prevent flashback ignition Long 3-1/2" (88mm) length arrester allows safe, secure placement of gas nozzle.
- Gasoline, Gas-Oily Mixture, Kerosine, Diesel
- Ergonomic offset fill port with comfort lift lever makes filling easier than ever Easy-to-use Safe-Squeeze® trigger for accurate control of liquid flow
- Self-closing lid controls vapors and spills
More Specification..!!
Justrite 7250130 Galvanized Steel, AccuFlow Type II Red Safety Can with 1" Flexible Spout, Large ID zone, Meets OSHA & NFPA For Handling Hazardous liquids. 5 Gallon (19L) Size.
Tuesday, December 13, 2011
Make Money Solving Plumbing Problems
Owners or tenants pay you to solve plumbing problems in their apartments or homes. Since this is an emergency type service, you should be able to make money without much trouble. People seem to have leaking water, and/or stopped up drains quite often. With the right kind of knowledge, you can easily solve most of these problems. (This is article #4 in a series of emergency handyman services.)
Requirements
This business idea is best suited for people who are physically fit and enjoy working with their hands. You must be able to locate and remedy common plumbing problems. If needed, you can buy how-to manuals at most plumbing or building products stores.
You should own a pickup truck or van to haul equipment, materials, supplies, and trash. You need to own or purchase the equipment and protective gear required for this activity. You should set up a home office with the basic office equipment and supplies.
Getting customers
Use a simple classified advertisement in the local newspaper or on craigslist.org to get customers. Also, advertise in any property owner's newsletter.
Preliminary job activities
After arriving at the job site and greeting the customer, inspect the water leak or stopped up drain. Determine if you need to purchase any plumbing fixtures, drainpipe, or water pipe. You should already have a supply of assorted drain traps, gaskets, screws, and washers for minor repairs.
The customer may be in a hurry and want you to work on a holiday, weekend, or at night to get the plumbing problem fixed.
You can use standard job bid forms to estimate your labor and the costs of materials and supplies. This bid should include the fees for any extra services to be performed, such as hauling away any large amounts of trash. If the customer accepts your bid, you both can sign the bid form.
Turn off the main water supply valve. Also, shut off any electricity or combustible gas to an affected water appliance.
Main job activities
Following are typical plumbing problems you may encounter and the procedures to take care of them.
Clogged aerator or showerhead -- The aerator is a device on the end of a faucet spout that mixes air with water to produce a gentle stream of water. A showerhead often is adjustable to allow different streams of water, such as a fine spray or a concentrated spray. You can unscrew either device from its spout and open it up to remove all the clogging particles inside it. Then screw the device back onto its spout.
Defective hot water tank -- If the tank itself is leaking it will have to be replaced. Sometimes a heating element on an electrical hot water tank burns out. In this case, only the heating element has to be replaced. If the hot water tank has to be replaced then the defective tank will have to be hauled to a suitable dumpsite. In most cases, a defective hot water tank should be repaired or replaced only by a licensed plumber. (Note: Draining, refilling, or replacing a hot water tank is a very delicate operation. Be sure you are fully qualified before attempting these procedures.)
Frozen water pipe --If the frozen water pipe is ruptured, turn off the main water shutoff valve. Then you will have to cut out the portion of the pipe that is split or ruptured. Place a water pail under this gap. Next heat the pipe beginning where the pipe was cut off and going both ways toward the rest of the pipe. After thawing out the pipe, you will have to replace the missing portion of the pipe. Then open a faucet and turn on the main water shutoff valve to verify that the pipe has been thawed out.
If the frozen water pipe is not ruptured, do not turn off the main water shutoff valve. Begin heating the pipe starting from an open faucet and going toward the portion of the pipe that appears to be frozen. Usually this will be where the pipe is exposed to cold air.
You can use any of the following heat sources to thaw out the pipe:
* Electric heat tape
* Heat lamp
* High-power air dryer
* Small portable heater
Do not use an open flame to thaw out a frozen water pipe. This may cause a fire.
Leaking bathtub or shower -- Any leaks from the showerhead or tub spout should be obvious from visual inspection immediately after use. You may be able to fix the leak by putting Teflon tape on the threaded pipe that supports the showerhead or tub spout. If the showerhead or tub spout is rusted out, you will have to replace it.
If the shower drain, or the bottom drain in a bathtub, is leaking as seen from water stains underneath it, you probably need to install a new gasket or plumbing putty between the drain flange and the shower or tub floor. If the side drain (overflow drain) in a bathtub is leaking as seen from water stains underneath it, you probably need to install a new gasket between the outside wall of the tub and the flange of the overflow drain.
If the seams in the bathtub wall or shower enclosure have opened, you will have to reattach the wallboard and/or apply new caulking. Also, you may need to renew the caulking between the bottom of the shower or bathtub wall, and the top edge of the bathtub or shower drain pan.
Another possible source of leaks is water spraying through the gaps where a shower curtain fails to butt firmly against the wall on either side. You can use adhesive caulk to attach plastic triangles to the top edges of the bathtub to close these gaps.
Leaking drainpipe or trap -- The two main causes of leaks from a drainpipe are a rusted or damaged pipe, or a worn-out gasket.
If there is no gasket at the source of the leak, then the drainpipe itself is probably damaged. You will have to replace that piece of the drainpipe. This drainpipe is usually either white thin-wall plastic, chromed metal, ABS black plastic, or galvanized steel.
If the drainpipe goes under the floor, you may have to get access to the crawl space or basement to locate the source of the leak.
When replacing a portion of a drainpipe that goes inside a larger pipe, be sure to allow for the "hidden" portion of the replacement drainpipe. Where different kinds of drainpipe are connected together, you'll need a compression nut and a new gasket for the connection.
Leaking faucet -- A standard faucet (or hose cock) is used for either cold water or hot water. Thus, two faucets are needed to deliver the desired temperature of water to a sink, washbasin, showerhead, or tub spout. A hose cock is a shutoff valve that allows the female end of a garden hose to be attached to its spout. It is used as a water supply for a clothes washer or a lawn sprinkler, or as a drain for a hot water tank.
The standard faucet (or hose cock) has a rubber washer that bears against a valve seat, the source of water. The washer is held in place by a screw that goes into the stem (spindle) of the handle.
A single-handle faucet controls the water temperature by mixing hot and cold water together. Depending on the manufacturer, these faucets use different devices to mix and control the flow of water. This device could be a cartridge, ceramic disc, or rotary ball with two rubber seats and springs. If this device is leaking, you will have to replace it.
Leaking toilet --If the toilet is a single piece, the leak will be where the toilet sits on the floor. You will have to unfasten the toilet from the floor, replace the wax ring, and re-fasten the toilet to the floor.
If the toilet has a separate water tank, the leak may be where the bottom of the water tank attaches to the top of the toilet bowl. If so, you will have either to carefully tighten the screws or replace the gaskets.
Leaking water appliance -- a water appliance refers to a dishwasher or clothes washer. The two main sources of leaks in a dishwasher are the hot water supply line and the drain line. You have to remove the kick plate of the dishwasher to get access to the underside of the dishwasher. While the dishwasher is running, you can inspect these two lines to see where the leak originates. To fix the problem, you probably need to tighten or replace the connection between the dishwasher and the water or drain line.
There could also be a leak where the other end of the hot water supply line goes into its shut off valve. If so, you probably need to tighten the connection or replace the washer.
A clothes washer is connected to the hot water and cold water supply with a pair of short hoses. These hoses are similar to a garden hose, but are stronger. You may have to tighten the connection or replace the washer. If the drain line connection to the clothes washer is leaking, you should tighten it or replace the washer.
Stopped up drainpipe or trap -- If the trap is blocked, you can simply unscrew it and dump out the water and any blocking material. Once the trap is cleaned out, any further blockage would be in the drainpipe after the trap. Remove the trap again and use an auger to clean out the drainpipe.
Stopped up toilet -- If the toilet bowl is overflowing, the blockage is either in the internal trap in the toilet, or in the drainpipe going from the base of the toilet to the sewer line. In either case, you probably need to use an auger to clear out the obstruction.
Final job activities
Turn the main water supply valve back on and turn on any electricity or combustible gas that was previously shut off. Check for any leaks or drain blockages. Inspect the premises to verify you have finished all required tasks. Remove all your equipment and supplies.
Collect your agreed upon fee from the customer. Haul large amounts of trash away, if part of your agreed upon services. (Remove small amounts of trash as a courtesy to your customer. You can haul it to a dumpsite later.)
Final thoughts
This business idea lets you make money while providing a needed service. You can start out as a part-time venture. Then, if the demand is sufficient, you might want to make it into a full-time venture.
Cheaper Fire And Water Safe Shop Alico Hiking Boots Prices Coffee Grounds Emesis
Friday, December 2, 2011
Handy Items Offer Quick Repairs Around The House
Strolling through your favorite hardware or home improvement store can be a lesson in ingenuity and provide the average homeowner with a wealth of widgets, gadgets and products that can save time, trouble and money on your next repair project. Many small inexpensive items have been developed to assist the homeowner in completing their next project in record time. They range from small metal parts that are used to repair a hole in a wall or ceiling to painting and electrical troubleshooting. We will examine what is available to the homeowner of today so that they can put these time saving products to work and spend more time having fun instead of working all weekend!
Repairing Drywall
The Insta-Back clips are a clever little metal clip that is slipped into the edges of a hole in a gypsum board wall or ceiling, the repair panel is then put in place. Screws are used to secure the panel in place, the tabs are bent back and removed leaving the surface ready to patch with tape and spackle or drywall mud. They are inexpensive though worth many times over their cost in time savings alone. This product is made by Construction Materials and are found in most home improvement centers and hardware stores for around .09 to .00 for a package of six and come with screws right in the package.
Wet & Set repair patch manufactured by Hyde Tools is another hole patching tool and all you need to do is to cut the patch to size and dip the patch into a pail of warm water, let drip and apply to the wall. Then just let the patch dry for thirty minutes and cover with your favorite patch material. They are available in a 4x4 or 6x6 inch sizes and can be found at your local hardware or home improvement center, they retail for .49 to .99 each depending on size. These patches take a little longer than the Insta-Back clips but the advantage is you do not need a piece of drywall to fill the hole and they can be used on rounded surfaces.
Installing a Ceiling Fan
All fans are installed in a similar manner and rely on the utilitarian ceiling box for support of the fan during operation. Each manufacturer requires a fan-rated or reinforced ceiling box for their products to be installed safely. This is easer said than done! However there is a new product that is on the market that promises to alleviate the problems associated with this critical installation step. The FAN-EZE product installs through the existing ceiling box itself in 2 minutes or less and is installed with common hand tools. It comes with all the hardware right in the package and is made by EE Products Inc. This product allows the ceiling box to be able to carry loads that are above that of fan-rated ceiling boxes, and best of all it is consumer friendly. The cost of this time saving product is .60 each and will allow a ceiling fan to be installed in less than an hour from start to finish.
Adhesives
A new product has been developed and released to the general public that mimics what has been available to industry for the last 10 years with commercial grade adhesives. Simpson has released an epoxy product that mixes in the barrel as it is extruded from the nozzle. All you have to do is squeeze the trigger and position the adhesive as it exits the nozzle, that's it. What is unique about this product is no special gun or fixture is required as the tube has been designed to fit in a standard caulking gun. The mess and bother that has plagued the two part epoxy systems is now a thing of the past. The Epoxy Tie system is available in a 1.7 and 10 fluid oz. sizes and retails for approximately .35 to .29 depending on which size you choose.
Not to be out done by anyone is 3M and their line up of ingenious no-mar type of adhesive solutions for applying hooks and other hardware to wall surfaces. These products are the Command Strips and allow the products to be placed on the wall and removed without leaving a residue, hole or mar of any kind to the wall surface. All that is needed to place the product is remove the protective adhesive strip cover and press it against the wall wherever you wish to hang that favorite painting or picture. What could be easier? To remove them slide the hook up and off of the anchor, then pull down on an elastic tab until the anchor is released. This product will be especially helpful to apartment dwellers that wish to decorate their apartments and are now free to express themselves without worrying about what the landlord will think when they move out. These products are available in a host of sizes and styles and retail for approximately .99 to .88 depending on size and configuration and can be found at most any hardware or home improvement center.
Super Glue Corporation has a patch material that can be used with practically any household material, plastic, metal, rubber, wood and fiberglass. This patch material is an adhesive patch that cures with sunlight or quicker with a cure lamp. You simply clean the area where the patch is to be installed and peel the adhesive cover off and press it into place. This patch would be handy to repair a hole in a gutter, or a garage door or even a skylight. The patch is a 6x3 inch sheet that retails for approximately .00. If your home improvement center or hardware store does not carry this brand there are other similar products on the market. Just read the label and make sure it is suitable for your intended application.
Frame Construction
For construction of a deck, an addition or maybe just a framing repair can be accelerated with the use of Simpson Strong Tie plates and brackets. The use of these stamped metal products increase the strength of the framing and are required for many framing tasks. The use of seismic or hurricane ties is required by just about all building codes across the country and are just a sample of what they manufacture. They make a myriad of products that are useful for just about any framing anchoring or connector need. These products will speed the completion of your next framing project so don't hesitate to look at the selection you are bound to find a product that suits your need.
These products are usually found in larger home improvement centers, hardware stores and lumber yards. The cost for these components varies with the product so just take your time and find the right components for your project.
Cabinetry & Hardware Repairs
Today's cabinets have been subjected to labor and cost cutting measures for several years. Much of the cabinet construction is now handled by hardware components, things like guides, rollers and stops are now metal and plastic where they were traditionally made from wood. So when that roller or guide breaks don't forget to look at the cabinet hardware section of your favorite home improvement center for a replacement. Home depot has a large selection so make it your first stop when looking for these components.
For smaller brackets, tie plates and reinforcement products and cabinet hardware check out the products manufactured by Stanley. The have a long tradition of providing quality hardware and tools that stretches back to 1843. They also have a large selection of hinges, striker plates, door knockers and other hardware as well so you are bound to find that item you need. The selection and cost of these components varies with the product but all are reasonable and will save you time and trouble.
Electrical Repairs
Nothing strikes fear into the average homeowner like an electrical problem. The good news is that there are a host of products that make the troubleshooting easier for the average homeowner. Gardner Bender makes a line of circuit testing products for receptacles and ground fault interrupted outlets. All you have to do is pug the tester into the socket and read the light display on the tester. The testers have a chart right on them that will tell you what the problem is so you can decide if you wish to tackle the problem or call in an electrician. These testers retail for .99 to .98 depending on which model you choose and are an inexpensive first step before deciding to call in a pro. For the more skilled or adventuresome they also make a simple twin probe circuit tester, the neon light type that can be used to tell if a receptacle or circuit is hot (current present) and also if the polarity of the receptacle is correct. These simple twin probe testers can be bought for about .00 to .00 dollars each depending on features and are a bargain by any measure. Almost all hardware stores, home improvement centers or lumber yard will stock these items.
For those that wish to finish their basement, attic or are adding a room to their house may want to look at the products being offered by Carlon. They have a line of plastic nail-on outlet, ceiling and receptacle boxes that are easy to install and offer time savings over the conventional metal products. The added advantage to these products is that do not need to be grounded since they are plastic and insulate the electrical wires inside of the box itself. Outlet boxes are inexpensive and can be found for as little as 21¢ when on sale. For ceiling boxes they sell in the 98¢ to .10 range depending on size and features. Carlon is one of the largest of the box manufacturers so you can find their products just about anywhere where home improvement and lumber products are sold.
Porcelain Fixture Repair
The next time you drop that heavy object on you porcelain tub, sink or fixture and see that chip go flying off into the sunset, don't despair Kit Industries with their Porc-a-Fix touch up glaze product has you covered. They have a large range of standard colors to choose from to match your sink or fixture and are applied by simply brushing the product on until the chip is filled. The standard colors retail for approximately .97 for a small bottle and are available in custom colors to match just about any need. Larger home improvement centers will carry these products but if you have trouble finding them just type porc-a-fix into your favorite search engine and a website that will serve your needs will pop up.
Painting
Is probably the most common home improvement project that homeowners will tackle? The good news is there are so many products that make it easier to paint your house than ever before. Foam Pro has a host of products that will make your job quicker and ease the clean-up afterwards. They have a whole range of disposable foam brushes and rollers and an ingenious new pour spout that clips on to the top of a one gallon can. This handy pour spout also has a brush edge to clean off your favorite brush since so many homeowners use the paint can as their paint bucket. This product sells for approximately 75¢ so include it with your next painting project.
The prep work prior to painting can be one of the most tedious chores about this type of project, cleaning the walls, patching the holes and cracks in walls seem endless. For holes Painters Nail Hole Filler has you covered, they manufacture a 4.5 fluid oz. squeeze tube of nail hole filler that you just place over the hole, squeeze and wipe away the excess in one easy motion. It retails for approximately .50 each. This product is sold at most of the home improvement centers and has the same name as the company.
Most of the walls and ceilings in peoples home today are textured from an orange peel to a knock down finish. Acoustic ceilings were popular some years ago but all of them pose a problem when a repair has been made and they lack the surface texturing. Matching the texture has been difficult in the past since it required commercial equipment to apply these surface finishes properly. Homax provides an easy solution to this problem with a line of finishes that span all of the popular textures of yesterday and today and are packaged in a convenient 10 or 12 fluid oz. spray can. These products are known collectively as Easy Touch and can be found in most all hardware and home centers. They retail for between .00 & .00 and are quick and inexpensive solution to this once difficult task.
Aqua-Tainer Co. is one of those companies that staked their future on offering inexpensive products that provide real value. Their products will make your next painting project easier, cleaner and quicker if you choose to make use of their of their various product offerings. One of the biggest mistakes the average homeowner makes when starting a painting project is using the one gallon paint can as a paint bucket when they start the cutting-in process. The bucket is heavy and exposes the paint to the air and starts the drying process right in the can even before much of the paint has been applied. It also contributes to fatigue having to carry this heavy container of paint around. The paint can does a very poor job of cutting off the excess paint on the brush so you should avoid making this mistake. They have very good solution for this problem with their Trim & Cut-In cup it holds about a pint of paint and has a cut-off edge made right into the cup. It is light enough so that holding the cup will produce little if any fatigue and if it is dropped only a small amount of paint is lost and will be much easier to clean up. This product retails for .98 on average. They also have another handy product with their P-38 five gallon bucket opener. It has been designed to open metal or plastic buckets and is a handy tool to use when you are handling these size containers. The best part is that it sells for only .97 and will save you the hassle of wrestling with opening these containers so the cost is more than worth it.
If the last two products were not enough they make a product called Carpet Shields each package comes with six three foot pieces for eighteen feet total of reusable shields. They are a masking strip that is inserted between the carpeting and the wall and protects the carpet and moldings from paint splatter or an over zealous paint brush. They retail for an unbelievable low price of only .87 for all six pieces. Buy several and be done with it, again most of the major home centers and hardware stores will carry these products.
I hope this stroll through your favorite home improvement center has been useful and informative. I have learned of many of these products through trial and error through the years and I find myself prowling the aisles of home centers just to stay abreast of the latest offerings. The advantage of using many of these low cost items is the time and hassle you save which relate to a less stressful project which can sometimes make the difference between success and failure.
Subscribe to:
Posts (Atom)
|
|
|
|
 |
 |
 |
 |
 |
 |
 |
 |